PRODUCTS QUALITY ORDER/QUERY FORM
CT 27. Devil Attrition Testing Machine IS 2386 (IV)
CT 28. Dorry Abration Testing Machine ALSECmake
CT 29. Drop Ball Impact Tester as per B.S.Spec.
CT 30. Extensometer in case with Dial Guage : reading 0.002 mm per Divn. for con-cylinder
CT 31. Entrain Meter Air cap.7 c.ft. or 0.007 c. mtr. ALSEC Make
CT 32. Flexure Attachment for Compression Testing Machine
CT 33. Flow Table : IS 712-1956 for Lime-steel top 30 cm dia
CT 34. Flow Table : IS 1727 for cement, Brass top, 25 cm
CT 35. Flow Table : IS 1727 (Motorised for cement, Brass top 25 cm)
CT 36. Flow Table : IS 1199-1959, Hand operated, for concrete with steel top 30'' dia (76.2 cm)
CT 37. Gillmore Needle as per A.S.T.M. ALSEC make
CT 38. Gauging Trowel per IS 269/1727
CT 39. Gauge Length (per IS 2386 (I)) ALSEC make
CT 40. Gauge Thickness (per IS 2386 (I))
CT 41. Hand Scoop
CT 42. Hammer Concrete Test, Non-destructive test (Medium)
CT 43.

Hydraulic jacks with (separated pumping unit) with 2 meter long flexible coupling tube.(Remote control type with pressure gauge)

(i) Capacity 5 Tons
(ii) Capacity10 Tons
(iii) Capacity 15Tons
(iv) Capacity 20Tons
(v) Capacity 25 Tons
(vi) Capacity 50Tons
(vii) Capacity 100Tons
(viii) Capacity 200 Tons
ALL ALSEC Make
CT 44.

Hydraulic Jacks Bottle type.ALSEC make

(i) Capacity10 Tons
(ii) Capacity 15Tons
(iii) Capacity 20Tons
(iv) Capacity 25 Tons
(v) Capacity 50Tons
(vi) Capacity 100Tons
CT 45. Hydrometer as per IS 2720 or A.S.T.M
CT 46. Kelly Balll Penetration Appartus Per A.S.T.M
CT 47. Length Comprator-(Frame only) with std. Bar
CT 48. Length Comprator with dial gauge0.002 mm/DIVISION for use with Cement Autoclave ALSEC make
CT 49. Length Gauge, I.S.2386 (I)
CT 50. Laboratory Concrete Mixer.cap 1.5 c. ft. (Motorised)
CT 51. Laboratory Pulverizer with 3 HP Electric Motor ALSEC make
CT 52. Le-Chatlier Mould Per IS 269, with glass plates & lead weight
CT 53. Le-Chatlier Mould and Hot Water Bath (set of six) L. Moulds Set
CT 54. Los Angles Abrasion Testing Machine with Rev. Counter & 12 Nos. Steel Balls (Abrasion charge)
CT 55. Mixer Morter : Roller type, Motorised
CT 56. Morter and Pestle
CT 57.

Moulds, cubes with Base Plate, Made of Cast Iron Per IS 516

(i) Size 2 inch or 50 mm of Cast Iron
(ii) Size 2.78 inch or 75 mm made of Steel plate.
(iii) Size 3 inch or 7.06 mm C.I.
(iv) Size 4 inch or 100 mm C.I.
(v) Size 6 inch or 150 mm C.I.
(vi) Size 8 inch or 200 mm C.I.
(vii) Size 12 inch or 400 mm C.I.n
ALL ALSEC Make
CT 58. Moulds Cylinder with Base Plate (Cylindrical Moulds)
Made of Cast Iron, Split type in two halves

(i) Size 1.1/2'' dia x 3'' ht. or 3.75 cm x 7.5 cm
(ii) Size 2'' dia x 4'' ht. or 5 cm x 10 cm
(iii) Size 3'' dia x 6'' ht. or 7.5 cm x 15 cm
(iv) Size 4'' dia x 8'' ht. or 10 cm x 20 cm
(v) Size 6'' dia x 12'' ht. or 15 cm x 30 cm